Nice looking GTC in blue

I was organizing my photo program a few days ago and found this photo of a nice looking GTC to share with you.
We had 3 dark blue GTC’s at this time and I think this car was sold to a guy in Switzerland.

Over the last Month I’ve been disassembling a dark blue1967 Ferrari 330 GTC to re-finish the paint, chrome and interior. Even though Pininfarina did a spectacular job building these beautiful Ferrari Coupe’s, there are some things that I can’t live with. These photos show the fit between the “B” pillar cover trim and the “C” pillar window surround trim just behind the door. The gap was enormous on both sides and was filled in with black urethane rubber from the factory. I ground off the chrome and copper and welded some new brass on the trim (which is made of brass) to tighten up the gap.

Trim on GTC Ferrari

Ferrari Pininfarina detail

Brass welding and fitting

Another area that bothers me on the most of the Ferrari GTC’s that I have seen is the fit of the center console at the shifter opening. Like the other cars I have looked at, the shifter isn’t centered in the opening so naturally, I have to adjust this area too. This GTC used to have an odd reverse lockout tab like some of the 60′s race cars, but it didn’t fit so someone bent up the sheet metal in the opening on the left side of the opening.

GTC Interior

Now it fits properly

Carrozzeria Touring Berlinetta

Ferrari Headlight detail

Touring Carrozzeria Body Dashboard

High Build Primer Ferrari

Here are a series of photos of the block sanding process on the Ferrari 166 Touring Berlinetta. The sheet metal is all sorted and gaps are perfect but the body needs hundreds of hours of serious elbow grease (sanding) to make sure it is all straight as an arrow. Syl isn’t scared of the “mud”, he completely fills in all of the door and hood gaps allowing him to block sand right across them so when the light hits the highly polished top coat you won’t see any waves or change in reflection.

Even though the grill we made fit the opening in bare aluminum, Syl spends hours making it perfect with skim coats of body filler and attacks the headlight rim contact areas with the same level of perfection. There isn’t any room for error when working with super fine trim that is used all over this car like the delicate headlight rings and the low profile windshield and rear glass surrounds. Imagine these surrounds,  start with a long  section of 1/4″ aluminum rod and whittle it down so only a quarter of it is used.  We re-made this trim because the delicate original material was destroyed when the car was disassembled.

Right now, the car is sealed up in high build primer with a blue tinted epoxy primer that seals the polyester filler from moisture and greasy finger prints. Now we have some more fitting here and there before it goes back to Syl’s shop to work out some more details such as the incredibly complex belt-line crown that goes from the headlight to the tail light..

We’ll probably have more hours in sanding and painting the dashboard that it would take to paint an entire late model car like a Mercedes or Honda. The dash on this car is a thing of beauty but it requires a perfectionist sicko to finish it because like the rest of the car, the trim that surrounds the gauges and switches are like string bikinis

Here are some photos for Derek who seems to get very turned on by Ferrari engine photos, mostly the “basamento” which translates to “base” and in this context it stands for Engine Block.

Testa Normal

Bassimento 250 GT Ferrari

Here is a early Porsche 911 Engine that Casey has finished and will hopefully be running later this week.

We often pick on people who say “all you gotta do is”, because there’s no such thing as “all you gotta do is”…. Anyone who says “all you gotta do is” either has never done it before or is trying to beat you up on an estimate. AKA, a looser

Most of the cars we work on have brand new brake components available to purchase which allow us to slam ‘em in and ship it. Unfortunately, we have to rebuild brake components on Ferrari’s which really sucks.  All you gotta do is…  Ugh. A guy sent me a totally blown out Master cylinder for a 330 GTC, rusted and stuck, terrible, horrible, so I sent steel fittings off to be cadmium plated, sent the cylinder to have a new sleeve installed in the bore, ordered an overhaul kit and when everything returned, I put it all back together. After assembling it the I noticed that the pistons were sticking in the cylinder so I took it all apart and the wrenches scratched the fresh plating and watched as the brake fluid stripped the black paint. I honed the bore and got the pistons to move freely, assembled it again and set it up to be tested on my high tech device that you can observe in the photo below. Now I am finding that the sleeve wasn’t drilled correctly and fluid couldn’t  into the forward chamber (that goes to the rear brakes) so I had to start all over again, scratching, chipping. Now, the cylinder is all back together and working perfectly after 7 hours of labor! “All you gotta do is”! Did I mention that the rebuild kit didn’t come with the correct first seal, there was a 30mm seal included when I needed a 25mm seal so after buying 3 kits, I resorted to making my own seal.

Ferrari GTC Brake Master Cylinder

I’m getting frustrated with all the photos in my IPHOTO window, every single image is washed out and nasty so its high time to replace the trusty D10, also known as “the childs toy”.  The D10 is great for a shop like ours (or a child toy box) because it can handle a nasty shock from being banged or dropped and it’s waterproof. I had so much fun to taking photos and videos of people underwater with their hair floating around in the artsy looking natural sepia tone of the river water. The D10 is a great camera and it won’t be tossed, it’ll just be downgraded for non glamorous work on dirty projects.

It smokes when the flash goes off, there are paint drips on the body and the lens has some welding spatter baked in, she-is-the Power Shot! No retractable lens to get jammed up with metal shavings, rugged body, she’s a good ‘ol girl.

For more glamorous shots I will use my new CANON G10! It isn’t a child’s toy. It is just what I was looking for, not a highbrow SLR but a super high tech point and shoot. It takes good video and amazing photographs, I’m really happy with it.

I don’t have many name brand loyalties, I think the Supermarket brand Oreo’s are better than Nabisco OREO’s and think pencils with my name on them are better than Dixon Ticonderoga but I must have Canon cameras.

Green Iron bridge 1908

Bridge in VT 1908

Canon D10 Powershot

A friend of mine is looking to sell this BMW Isetta to free up some space for other cars. This is one of the best Isettas I have ever  seen because he had all the details done properly right. If you are looking for an Isetta let me know and I can connect you with the owner.

BMW Isetta for sale

We seem to have an influx of 250 engines all of a sudden, the one Nate is working on just completed its first test run on the bench after overhaul and the other is coming apart because of problems with the cylinder heads. On this engine, the valve guides are loose in the heads allowing oil to pour into the exhaust system that made smoke pour out of the exhaust system once it heated up.

Bill took some video of the other engine running on the test stand so keep an eye out for that clip on youtube soon.

Ferrari 250 engines

Cylinder heads 911 Porsche

Porsche 911 Crank Case

Inside view of the 911 engine

Over the last few years we have overhauled a bunch of Porsche 911 engines that have the same description as this one, it runs OK but smokes and leaks a bunch of oil. Once we get inside and check things out we find a whole host of issues from collapsed chain tensioners, broken piston rings and wiped out bearings. This engine has a few severely scratched piston skirts and hosed thrust bearings and intermediate shaft bearings.

It’ll be great to get all these parts cleaned up, freshened up and dialed in so the customer can have the car rocking and rolling for the spring. The engine is equipped with Weber Carburetors which seem good but are they better than the Bosch Mechanical Fuel Injection?

These 330′s look so spectacular to me when painted in a bright color like this light blue or silver. We’ve done tons of work to this car to make it run and drive better than it looks.

Something about the rear of the car, the “C” pillar area above the rear wheel looks so great, so clean and pure. How can you argue with Italian design!

Ferrari 330 GT Blue