Here is a video of the engine running on the test stand to check for leaks and the adjustment of the ignition system and carburetors. This engine has German made Solex/Zenith carburetors, an Italian produced Magnetti Marelli distributor in combination with a French S.E.V Marchal Alternator.

Here’s a youtube link to see the engine running on the tabletop

Rebuilt 911 engine

The engine is running great and just today we took the car out for a drive in the Arctic Cold air where it performed perfectly.

Testa Normal

Bassimento 250 GT Ferrari

Here is a early Porsche 911 Engine that Casey has finished and will hopefully be running later this week.

GTC for Sale 330

Here is a Super nice 330 GTC that a customer of ours is interested in selling. We’ve gone through all of the mechanical components within the last two years such as the engine, transmission and numerous other details. This car is outstanding and is ready to light ‘em up for 2012!

This transmission works well but the synchronizers are worn to to point of having a chrome plated polished look instead of the required rough cast finish but all the bearings and gears are perfect. We used to replace the operating sleeves on these transmissions but they take so long to “wear in” that I feel they are doing more damage than good especially considering how well they shift with the original parts re-installed.

5-speed 330 Transmisison

Head gasket and oil leaks

Since the late 80′s or early 90′s we have been servicing the car that goes with this engine and it has always been one of the best running examples we know of. I remember riding in the truck with my father to get the car on a cold and foggy night, probably around this time of the year, no, it had to have been early November. It was a brutal trip through that pea soup thick fog as we went over some of the mountains in the Berkshires on route 22.

The current owner of the car drives the wheels off of it and we have overhauled a number of components like the brakes, transmission, and fuel pump but now it’s time to address the engine. It runs great, starts instantly and doesn’t smoke but there are so many oil leaks that we have to break it down to clean it off in order to remedy them. We were blown away because as well as it ran, the compression and leak down numbers were bad displaying 30% loss in some cylinders where there should be no more than 5-10%.

So, apart it goes – it’ll run through our “process” that includes getting the rear main bearing cap cut and grind the crankshaft for a conventional lip seal, new forged pistons and a needle bearing roller follower set among thousands of other things. The motor mounts are blown out and the water pipes will likely have holes in them and will need to be replaced so we will be busy this winter getting all these 250′s back together for the spring.

As much as I hate to mention it for superstitious reasons, we’ve had great success with Ferrari engine overhauls over the last half a dozen years. A few times a week other shops call me asking how to get head gaskets to seal and how to make water pumps turn without leaking or how to make mechanical fuel pumps to work as intended. Their shops are struggling to find the exact formula, and we seem to have it locked down lately. Nate has assembled so many of these engines, he seems to have a real formula on setting the clearances, knowing the tricks to seal them up and making sure every detail is nailed down too.

Clutch housing on 250 engine

Most of the cars we work on have brand new brake components available to purchase which allow us to slam ‘em in and ship it. Unfortunately, we have to rebuild brake components on Ferrari’s which really sucks.  All you gotta do is…  Ugh. A guy sent me a totally blown out Master cylinder for a 330 GTC, rusted and stuck, terrible, horrible, so I sent steel fittings off to be cadmium plated, sent the cylinder to have a new sleeve installed in the bore, ordered an overhaul kit and when everything returned, I put it all back together. After assembling it the I noticed that the pistons were sticking in the cylinder so I took it all apart and the wrenches scratched the fresh plating and watched as the brake fluid stripped the black paint. I honed the bore and got the pistons to move freely, assembled it again and set it up to be tested on my high tech device that you can observe in the photo below. Now I am finding that the sleeve wasn’t drilled correctly and fluid couldn’t  into the forward chamber (that goes to the rear brakes) so I had to start all over again, scratching, chipping. Now, the cylinder is all back together and working perfectly after 7 hours of labor! “All you gotta do is”! Did I mention that the rebuild kit didn’t come with the correct first seal, there was a 30mm seal included when I needed a 25mm seal so after buying 3 kits, I resorted to making my own seal.

Ferrari GTC Brake Master Cylinder

Bill took some video of the other engine running on the test stand so keep an eye out for that clip on youtube soon.

Ferrari 250 engines

Cylinder heads 911 Porsche

Porsche 911 Crank Case

Inside view of the 911 engine

Over the last few years we have overhauled a bunch of Porsche 911 engines that have the same description as this one, it runs OK but smokes and leaks a bunch of oil. Once we get inside and check things out we find a whole host of issues from collapsed chain tensioners, broken piston rings and wiped out bearings. This engine has a few severely scratched piston skirts and hosed thrust bearings and intermediate shaft bearings.

It’ll be great to get all these parts cleaned up, freshened up and dialed in so the customer can have the car rocking and rolling for the spring. The engine is equipped with Weber Carburetors which seem good but are they better than the Bosch Mechanical Fuel Injection?